ASA上配置Active/Active Failover
文章摘要: ASA Active/Active Failover只能配置在多模式下 l 如下图配置 ASA : Context Interface IP Address Nameif c1 e0 30.1.1.10 outside e1 10.1.1 .10 inside Context Interface IP Address Nameif c2 e0 30.1.1.20 outside e2 20.1.1 .10 insid
ASA Active/Active Failover只能配置在多模式下
l 如下图配置ASA:
Context Interface IP Address Nameif
c1 e0 30.1.1.10 outside
  e1 10.1.1.10 inside
Context Interface IP Address Nameif
c2 e0 30.1.1.20 outside
  e2 20.1.1.10 inside
l 使用E3口作为拷贝配置文件和状态信息的接口;
l Failover IP地址为192.168.1.1 255.255.255.0 192.168.1.2;
l Failover key为ciscoask;
1.配置交换机
2.配置ASA1
基本配置同上,我们只配置A/A的Failover;注意:A/A的failover只运行在多模式防火墙上;
asa1(config)# failover lan enable
asa1(config)# failover lan unit primary
asa1(config)# failover lan interface failover e3
INFO: Non-failover interface config is cleared on Ethernet3 and its sub-interfaces
asa1(config)# failover link failover e3
asa1(config)# fail inter ip failover 192.168.1.1 255.255.255.0 standby 192.1681.2
asa1(config)# failover key ciscoask
//A/A的Failover是以Failover组来实现的,虚拟防火墙加入组,组在设备上为active,那么
该虚拟防火墙就为active;
asa1(config)# failover group 1
asa1(config-fover-group)# preempt        //配置抢占
asa1(config-fover-group)# primary
asa1(config)# failover group 2
asa1(config-fover-group)# preempt
asa1(config-fover-group)# secondary
asa1(config)# context c1
asa1(config-ctx)# join-failover-group 1
asa1(config)# context c2
asa1(config-ctx)# join-failover-group 2
asa1(config)#failover
2.配置ASA2
范冰冰素颜做公益ASA2的Failover配置不变;
3.测试
在ASA1上show failover
asa1(config)# show failover
Failover On
Cable status: N/A - LAN-based failover enabled
Failover unit Primary
Failover LAN Interface: failover Ethernet3 (up)
Unit Poll frequency 15 seconds, holdtime 45 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 4 of 250 maximum
Version: Ours 7.2(2), Mate 7.2(2)
Group 1 last failover at: 21:48:59 UTC Dec 3 2007
Group 2 last failover at: 21:48:58 UTC Dec 3 2007
十二月你好
  This host:    Primary
Group 1      State:          Active
                Active time:    105 (sec)
Group 2      State:          Standby Ready
                Active time:    0 (sec)
                  c1 Interface outside (30.1.1.10): Normal
                  c1 Interface inside (10.1.1.10): Normal中国著名服装品牌
                  c2 Interface outside (30.1.1.250): Normal
                  c2 Interface inside (20.1.1.250): Normal
Other host:  Secondary
985大学有哪些 Group 1      State:          Standby Ready
                Active time:    0 (sec)
  Group 2      State:          Active
                Active time:    105 (sec)
                  c1 Interface outside (30.1.1.250): Normal
                  c1 Interface inside (10.1.1.250): Normal
                  c2 Interface outside (30.1.1.20): Normal
                  c2 Interface inside (20.1.1.10): Normal
英语六级作文模板Stateful Failover Logical Update Statistics
        Link : failover Ethernet3 (up)
        Stateful Obj    xmit      xerr      rcv        rerr
        General        151        0          143        0
        sys cmd        143        0          143        0
        up time        0          0          0          0
        RPC services    0          0          0          0
        TCP conn        0          0          0          0
        UDP conn        0          0          0          0
        ARP tbl        8          0          0          0
        Xlate_Timeout  0          0          0          0
        Logical Update Queue Information
                        Cur    Max    Total
        Recv Q:        0      1      143
asa1(config)#
转载请注明文章来源——【思科学习问答网】
吃槟榔的好处 转载请注明文章来自:【思科学习问答网】www.ciscoask/a/jishuzhuanti/_wangluoanquan_/_fanghuoqiangjishu_/2010/1226/289.html